English
Products
25A Miniature Circuit Breaker
  • 25A Miniature Circuit Breaker25A Miniature Circuit Breaker
  • 25A Miniature Circuit Breaker25A Miniature Circuit Breaker
  • 25A Miniature Circuit Breaker25A Miniature Circuit Breaker
  • 25A Miniature Circuit Breaker25A Miniature Circuit Breaker

25A Miniature Circuit Breaker

The 25A Miniature Circuit Breaker (MCB) provides overload and short-circuit protection for suitable commercial branch circuits. Available with C or D tripping curves, it can be specified for compatible air-conditioning units, small water pumps and single-phase fan circuits. DIN-rail mounting and multiple pole configurations support different distribution panel designs.
Motor-driven branch protection

Commercial air conditioners, water pumps and ventilation fans draw a starting current several times their running current. A breaker chosen only on the running rating may trip every time the compressor kicks in — or fail to clear a fault quickly enough when one occurs. The curve has to fit the start, and the breaking capacity has to fit the fault level.

The 25A Miniature Circuit Breaker gives you that choice. C curve as standard, D curve where the start-up surge is higher, and 6kA or 10kA breaking capacity selected against the prospective fault current at the panel. The thermal element handles sustained overload, the magnetic element handles short circuit, and both sit inside a standard 18mm module.

Mounting is 35mm DIN rail in 1P, 1P+N, 2P, 3P and 4P, with a three-position handle that shows on, off or tripped. The housing is flame-retardant PC. For motors that need tighter overload protection, the device works alongside a thermal overload relay rather than replacing it.

25A · C / D curve 25A miniature circuit breaker for air conditioner, water pump and ventilation fan circuits
25ARated current
6kA / 10kABreaking capacity
5–10× / 10–20×C / D magnetic range
1P–4PPole configurations
25A miniature circuit breaker front view with trip-indicating handle
25A MCB housing and terminal detail

Which Curve Fits Air Conditioners, Water Pumps and Ventilation Fans?

The starting current of a motor-driven load is the deciding factor. Compressors, pumps and fans can pull 3–8 times their running current for a fraction of a second up to a few seconds, depending on the load type. If the magnetic threshold sits below that surge, the breaker trips on every start — and the site calls it a fault when it is only a mismatch.

The 25A Miniature Circuit Breaker is offered in two curves so that mismatch can be engineered out:

C CurveSTANDARD
Magnetic tripping range5–10 × In
Best fitModerate inrush
Typical useVentilation fans, small AC units, general commercial branches
Watch forCompressor starts that exceed the magnetic threshold
D CurveOPTIONAL
Magnetic tripping range10–20 × In
Best fitHigher inrush
Typical useWater pumps, compressors, larger motor branches
Watch forFault-loop conditions and disconnection times

Pick the curve from the measured start-up profile of the equipment, not from the equipment name alone. A D curve does not guarantee that start-up tripping will never occur, and its higher magnetic threshold still has to satisfy the fault-disconnection conditions your installation design requires. For motors with a heavy start and long acceleration, a motor protection device may be the more appropriate protective component.

Key Specifications

Product Type Miniature Circuit Breaker (MCB)
Rated Current 25A
Tripping Curve C curve standard; D curve optional
Rated Voltage AC 230V / 400V; DC version available on request
Breaking Capacity 6kA / 10kA options
Number of Poles 1P, 1P+N, 2P, 3P, 4P
Mounting 35mm DIN rail
Housing Material Flame-retardant PC
Handle Indication Three-position handle with trip indication
Operating Temperature -25°C to +70°C
Protection Degree IP20; install inside a suitable enclosure
Single-Pole Dimensions 18mm wide × 80mm high × 66mm deep
Reference Standards IEC 60898-1, GB 10963.1

Confirm the trip curve, voltage rating, pole configuration and breaking capacity for the exact model before it is specified into a project.

Where This Breaker Fits

Commercial cabinet AC

Branch protection for packaged air-conditioning units where the compressor start is within the curve's magnetic range.

Small water pumps

Supply circuits for booster and transfer pumps, with the D curve considered where the start-up surge is high.

Ventilation fans

Single-phase extract and supply fans on equipment-room and workshop branches.

Equipment-room branches

Mixed HVAC and small-equipment circuits in plant rooms and service corridors.

Small commercial cooling

Cooling equipment where the nameplate current and starting characteristic are both known.

Retrofit replacements

Existing panels where a compatible 25A branch device is being replaced without reworking the busbar.

The 25A rating does not automatically make the breaker suitable for every device in these categories. Confirm the equipment nameplate, the wiring design and the local requirements before ordering.

25A miniature circuit breaker with D curve marking and terminal detail
25A MCB mounted on DIN rail inside a motor control panel

Where the MCB Sits in a Motor Circuit

On motor branches, the MCB provides branch-circuit overload and short-circuit protection within its rated characteristics. It is not the whole protection package, and it is not a replacement for motor overload protection. The roles split like this:

25A MCB

Branch-circuit overload and short-circuit protection within its rated characteristics.

Contactor

Switches the motor supply as part of the control circuit — start, stop and remote control.

Thermal overload relay

Additional motor overload protection tuned to the motor's actual running current and duty cycle.

Where the panel also carries surge protection, an SPD may be added — together with an SPD backup protector where the SPD manufacturer specifies dedicated backup disconnection. The full arrangement, including the distribution box layout, depends on the motor, the control method and the applicable electrical regulations.

Installation, OEM and Delivery

The breaker mounts on standard 35mm DIN rail with single-pole dimensions of 18mm × 80mm × 66mm. The IP20 rating means it is installed inside a suitable enclosure, so allow for ambient temperature, conductor routing, terminal compatibility and heat dissipation when the panel is laid out. Terminals should be tightened to the torque specified in the datasheet.

OEM printing is supported, so the cover, handle and packaging can carry your brand, part number and language set — send the artwork and tell us how you want the marking customized. Production runs in our China factory, and because we also build SPDs, backup protectors and distribution boxes, one supplier can cover the protection package for a panel project.

Quality control covers incoming material checks, controlled assembly, calibration of the thermal and magnetic elements, and a routine trip test before packing. Records are kept for the exact model — test data, traceability information and conformity declarations where available. IEC 60898-1 and GB 10963.1 are listed as reference standards; the reference does not by itself establish third-party certification, so check the documents against the model you are ordering.

For a quotation, confirm the trip curve, rated voltage, pole configuration, breaking capacity, branding requirements and the market-specific documents you need. Sample availability, MOQ, lead time and warranty terms are confirmed for the specific order.

Frequently Asked Questions

Should I choose a C-curve or D-curve 25A MCB for a water pump?

The choice depends on the pump's starting current and how long the start lasts, together with the circuit's fault-protection requirements. A D curve may suit a higher inrush current, but it is not automatically the correct choice for every pump. Measure or obtain the start-up profile first.

Can a 25A MCB be used with 4mm² copper cable?

It depends on the cable's installation method, insulation, ambient temperature, grouping, cable length and local wiring rules. Verify the corrected cable ampacity and the protection coordination before specifying the cable and breaker together.

Does this MCB provide complete motor overload protection?

It provides thermal-magnetic overcurrent protection, but it does not replace a dedicated thermal overload relay or motor protection device. The required arrangement depends on the motor and the circuit design.

How do I select the breaking capacity?

Check the prospective short-circuit current at the installation point. Choose a model whose breaking capacity and voltage rating suit the circuit, and confirm the pole configuration matches the supply arrangement.

Will a D-curve breaker stop nuisance tripping on compressor start-up?

It raises the magnetic threshold, which can reduce trips caused by inrush. It does not guarantee the absence of start-up tripping — if the start-up current exceeds even the D-curve range, or the fault-loop conditions do not allow the higher threshold, a different protective approach is needed.

Is OEM branding available?

OEM printing is supported. Confirm the logo, label artwork, model configuration, MOQ, sample arrangements and documentation requirements before ordering.

Send the motor, the start-up current and the panel fault level

We will confirm the 25A Miniature Circuit Breaker curve, pole configuration and breaking capacity for your circuit, and reply with samples, pricing and lead time.

Send Inquiry Now
Send Inquiry
Contact Info
Send your product requirements, target specifications and order quantities to discuss suitable electrical protection products, quotations and production arrangements with our team.
X
We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
RejectAccept