English
Products
20kA SPD Surge Backup Protector
  • 20kA SPD Surge Backup Protector20kA SPD Surge Backup Protector
  • 20kA SPD Surge Backup Protector20kA SPD Surge Backup Protector
  • 20kA SPD Surge Backup Protector20kA SPD Surge Backup Protector
  • 20kA SPD Surge Backup Protector20kA SPD Surge Backup Protector

20kA SPD Surge Backup Protector

The 20kA SPD Surge Backup Protector is a compact DIN rail device for coordinated backup protection of compatible Type 2 SPDs in floor distribution boards, security monitoring cabinets and small control panels. AC 230V/400V versions are available in 1P, 1P+N, 2P, 3P and 4P, each pole occupying 18mm of 35mm DIN rail, with flame-retardant PC housing and green/red status indication. An optional potential-free auxiliary contact supports remote fault signalling in distributed cabinets. The device does not discharge lightning current itself; suitability depends on the connected SPD, follow-current interruption performance and prospective short-circuit current. Send the SPD model, voltage, pole configuration and quantity for a factory quotation.

    In floor distribution boards, security monitoring cabinets and small control panels, surge protective devices help protect connected electrical equipment against transient overvoltages. Over time, an SPD may deteriorate or develop a fault that requires disconnection from the power supply.

    The 20kA SPD Surge Backup Protector for Type 2 Surge Protection Systems provides a dedicated backup protection function for compatible SPDs. When the connected SPD develops a qualifying power-frequency fault, the protector is designed to disconnect the affected branch under its specified operating conditions.

    Its compact modular design is suitable for installations where DIN rail space is limited or where multiple distributed electrical cabinets require a consistent protection arrangement. Available in 1P, 1P+N, 2P, 3P and 4P configurations, it supports different circuit designs. An optional auxiliary dry contact can provide a fault-status signal to a compatible monitoring system, helping maintenance teams identify a device that requires inspection.

    This device does not independently discharge lightning current. It must be selected and installed with a compatible SPD according to the system voltage, surge coordination requirements and fault-disconnection conditions.

    20kA classType 2 backup duty
    18mm per poleSpace-saving module width
    1P – 4PFive configurations

    20kA Type 2 SPD Backup Protector for Compact Distribution Boards20kA SPD Backup Protector Modular Housing for DIN Rail Cabinets

    When to Specify a 20kA SPD Backup Protector

    Not every Type 2 installation needs the same backup class. A 20kA backup protector is normally considered where the SPD duty is moderate and the panel is compact — typically a floor distribution board, a distributed CCTV power cabinet, or a small control panel feeding instrumentation and auxiliary circuits.

    Three questions decide whether this model is the right fit:

    • Is the connected SPD a compatible Type 2 device? The SPD manufacturer's backup protection recommendation is the starting point, not the kA figure on the label.
    • Is the fault level within the device's verified performance? Prospective short-circuit current at the installation point and follow-current interruption capability must both be checked.
    • Does the cabinet have the space? At 18mm per pole on 35mm DIN rail, this model is intended for panels where rail length is already committed to other devices.

    Where the SPD duty is heavier — main distribution or industrial incoming panels — compare this model with the 40kA SPD Surge Backup Protector or the 25kA SPD Surge Backup Protector before finalising the bill of materials.

    Key Features and Benefits

    Backup Protection for Type 2 SPDs

    Designed for compatible Type 2 SPDs in specified 20kA-class applications, the device provides a backup disconnection function when a qualifying SPD fault occurs. The exact coordination requirements should be verified against the selected SPD model.

    Space-Saving Modular Design

    The 35mm DIN rail mounting system supports installation in compact distribution boards, monitoring cabinets and small control panels. A single-pole width of 18mm helps make efficient use of available space, subject to the selected pole configuration and required clearances.

    Optional Remote Fault Signaling

    An optional potential-free auxiliary contact can connect to a compatible monitoring or alarm circuit. In distributed monitoring and security installations, this feature can help maintenance personnel identify a tripped device without checking every cabinet individually.

    Multiple Pole Configurations

    Available options include 1P, 1P+N, 2P, 3P and 4P. The correct configuration depends on the circuit arrangement, grounding system and protection design.

    AC and DC Selection

    The specified AC versions cover 230V and 400V applications. A DC version may be available for selected applications, subject to confirmation of the rated DC voltage, fault interruption capability and compatibility with the associated SPD.

    OEM Customization

    OEM product marking and packaging options can be discussed for project and distribution requirements. Samples may be requested for preliminary evaluation before confirming a bulk order.

    20kA SPD Backup Protector DIN Rail and Pole Configuration Detail20kA Type 2 SPD Backup Protector with Status Indicator and Optional Auxiliary Contact

    Technical Specifications

    Product Name 20kA SPD Surge Backup Protector
    Intended SPD Type Type 2 SPD; confirm model-specific coordination
    SPD Rating Reference 20kA class as specified; verify the applicable current rating and waveform
    Rated Operating Voltage AC 230V / 400V
    DC Version Optional; confirm model-specific ratings
    Available Pole Configurations 1P / 1P+N / 2P / 3P / 4P
    Mounting 35mm DIN rail
    Single-Pole Dimensions 18mm (W) × 80mm (H) × 66mm (D)
    Housing Material Flame-retardant PC, as specified
    Status Indication Green for normal status; red for fault/trip status, subject to final product marking
    Auxiliary Contact Optional potential-free dry contact
    Operating Temperature -40°C to +85°C, as specified
    Protection Degree IP20; for installation inside an appropriate enclosure
    Referenced Standards GB/T 33588.3 and IEC 61643; applicable parts and conformity to be verified

    Before specification approval, confirm the meaning of the 20kA rating, the applicable surge waveform, coordination with the selected SPD, follow-current interruption capability, short-circuit conditions and relevant standard editions. Verify all ratings against the datasheet for the exact model.

    Typical Applications

    The 20kA SPD Surge Backup Protector can be evaluated for compatible installations in the following applications:

    Floor distribution boards Security monitoring cabinets CCTV power cabinets Low-voltage distribution rooms Small control panels PV AC distribution, subject to verification

    Floor distribution boards: backup protection for compatible SPDs in residential and commercial buildings.

    Security monitoring cabinets: protection arrangements for distributed CCTV power cabinets and related electrical systems.

    Low-voltage distribution rooms: compact installations serving multiple electrical circuits.

    Small control panels: backup protection for compatible SPDs in control and auxiliary power circuits.

    Selected photovoltaic AC distribution applications: use only where the system design and selected SPD are compatible with the protector's verified ratings.

    The product is intended for use in a coordinated electrical protection arrangement. Actual suitability depends on the system design, SPD characteristics and applicable installation requirements. In cabinets that also house a distribution box layout or miniature circuit breakers, confirm the rail and wiring plan together rather than device by device.

    Selection and Installation Guide

    To avoid mismatches between the backup protector and the SPD, confirm the following details before ordering:

    Connected SPD
    Provide the Type 2 SPD model, rated voltage and relevant surge-current specifications.
    Power system
    Confirm the AC or DC application, system voltage and grounding arrangement.
    Pole configuration
    Select 1P, 1P+N, 2P, 3P or 4P according to the circuit design.
    Fault protection requirements
    Verify the available short-circuit current and the required follow-current interruption performance.
    Monitoring requirements
    Specify whether an auxiliary dry contact is needed and confirm its contact ratings.
    Installation space
    Check the DIN rail layout, wiring arrangements and enclosure requirements.
    Project documentation
    Confirm the required datasheets, test reports, standards and OEM marking details.

    Installation must follow the manufacturer's wiring diagram and applicable electrical requirements. Confirm the actual connection arrangement for the selected SPD and backup protector rather than assuming one universal wiring method. For the upstream SPD itself, refer to the Type 2 AC surge protection device selection data.

    Quality Control and Technical Documentation

    For distributed electrical installations, consistent product specifications and traceable test records can simplify technical review and maintenance planning. For the exact model and production batch, confirm the availability of relevant records covering:

    • Incoming material and component inspection
    • Insulation resistance and dielectric withstand testing, where applicable
    • Operating-function and fault-disconnection testing
    • Surge coordination testing for the intended SPD
    • Applicable temperature, damp-heat and aging tests
    • Product identification and batch traceability
    • Relevant third-party test reports and technical datasheets

    If third-party documentation is required for a project, verify the report issuer, product model, tested configuration and applicable standard. Do not assume that reports for one variant automatically cover every pole configuration or DC version.

    Frequently Asked Questions

    Can this 20kA backup protector provide lightning protection by itself?

    No. It does not independently discharge lightning current. It provides backup protection for a compatible SPD, which performs the surge protection function.

    Can I use a standard miniature circuit breaker instead?

    Not automatically. A standard miniature circuit breaker may have different surge withstand and follow-current interruption characteristics. Confirm suitability using the SPD manufacturer's coordination guidance, the protective device ratings and the installation requirements.

    Where should the device be installed?

    The installation position and wiring arrangement must follow the manufacturer's instructions for the selected SPD system. Confirm the required circuit topology before installation.

    Is remote fault signaling useful for CCTV and distributed monitoring systems?

    The optional auxiliary dry contact can provide a status signal to a compatible alarm or monitoring system. This can help maintenance personnel identify a tripped device and arrange inspection. Confirm the contact ratings and signaling function before integration.

    Can this model be used in a photovoltaic system?

    A suitable version may be available, but AC ratings must not be assumed to apply to DC circuits. Confirm the system voltage, fault interruption capability, grounding arrangement and compatibility with the selected SPD before ordering.

    What should be confirmed before a bulk order?

    Confirm the SPD model, operating voltage, pole configuration, application type, monitoring requirements, applicable technical documents, OEM details, MOQ and lead time.

    Are samples and OEM customization available?

    Sample availability and OEM marking or packaging options can be confirmed according to the requested configuration and order requirements. Contact us to discuss your specifications before placing a bulk order.

    Request Technical Information

    For distributed power distribution or monitoring cabinet projects, share the connected Type 2 SPD model, system voltage, pole configuration and any remote signaling requirements. This information helps establish whether the selected backup protector is suitable for your application.

    Need a compact SCB for a distributed cabinet project?

    Send the SPD model, voltage, pole configuration and estimated quantity — we will confirm the matching model, sample availability and bulk pricing.

    Send Inquiry

    Contact us for model-specific specifications, sample availability, OEM options and technical documentation for evaluation.

    Send Inquiry
    Contact Info
    Send your product requirements, target specifications and order quantities to discuss suitable electrical protection products, quotations and production arrangements with our team.
    X
    We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. By using this site, you agree to our use of cookies. Privacy Policy
    RejectAccept