The TU-SHAN Electric TZU-20 1P+N-PE Type 2 AC Surge Protective Device 20kA is designed for single-phase AC distribution systems that require protection against transient overvoltages caused by induced lightning surges and electrical switching events. Its 1P+N-PE configuration provides separate L-PE and N-PE protection paths for compatible distribution circuits.
With a nominal discharge current (In) of 10kA and a maximum discharge current (Imax) of 20kA under the specified 8/20 μs waveform, the TZU-20 is intended for Type 2 surge protection at downstream distribution boards and electrical cabinets. The specified voltage protection level is Up ≤ 1.0kV, subject to the applicable test conditions.
The device features a plug-in module design, an integrated thermal disconnection mechanism, and a visual status indicator. Individual modules can be replaced after safe circuit isolation, helping maintenance personnel identify and address a failed protection module without automatically replacing the complete assembly.
Confirm the ratings, wiring arrangement, and applicable test conditions against the technical datasheet for the exact TZU-20 configuration.
The 1P+N-PE configuration combines an L-pole module and a separate N-PE module. The specified protection paths are L-PE and N-PE, allowing the device to be considered for single-phase distribution circuits where this arrangement matches the system design.
The two modules have different maximum continuous operating voltages: 275V AC for the L-pole module and 255V AC for the N-PE module. Check the wiring diagram and earthing arrangement before selection. These voltage ratings alone do not establish compatibility with every electrical system.
In and Imax describe different discharge-current ratings under the specified 8/20 μs waveform. The TZU-20 is rated at In 10kA and Imax 20kA, making these values useful reference points when comparing Type 2 SPDs for a distribution board or control cabinet.
These ratings do not mean that the device can withstand every lightning event. Where the incoming supply requires Type 1 protection, select and coordinate an appropriate upstream SPD with the downstream Type 2 device.
When comparing a 1P+N-PE Type 2 AC Surge Protective Device 20kA with other models, buyers should assess the discharge-current ratings alongside the voltage protection level, earthing arrangement, and upstream protection requirements. The current ratings alone do not determine whether a particular SPD is suitable for an installation.
The plug-in construction allows individual modules to be replaced when required, supporting maintenance and spare-part planning. The visual status indicator helps personnel identify a module that needs inspection. Follow the product markings and instructions to interpret the indicator and determine when replacement is necessary.
Always isolate the circuit and verify that it is safe to work on before removing or replacing a module. Do not assume that a module can be replaced while the system is energized.
The TZU-20 can be evaluated for compatible 220V AC distribution boards in residential, office, and commercial buildings where downstream Type 2 surge protection is required. Final selection depends on the earthing system, upstream protection, and the installation's surge protection design.
For projects specifying a 1P+N-PE Type 2 AC Surge Protective Device 20kA, confirm that the 220V AC supply, L-PE and N-PE protection paths, and specified earthing arrangement match the installation requirements before ordering.
For monitoring cabinets and security equipment rooms, the device can be considered for compatible single-phase AC power circuits. Camera signal cables, Ethernet connections, and communication interfaces need separate protection selected for their respective circuits.
The TZU-20 may be used in suitable single-phase AC distribution circuits supplying UPS equipment and related electrical loads, subject to the UPS manufacturer's requirements and the overall surge protection arrangement.
Compatible AC supply circuits for PLC systems, instruments, temperature controllers, and other control equipment can be assessed for Type 2 protection. Signal and communication circuits require separate evaluation because this model is an AC power surge protective device.
The TZU-20 can be considered for compatible AC auxiliary power circuits in photovoltaic and energy storage installations. It is an AC SPD and must not be used as a substitute for a DC-rated SPD on PV strings or battery circuits.
Compatible AC control-power circuits in lighting systems and charging equipment may require transient overvoltage protection. Confirm the operating voltage, earthing arrangement, and equipment requirements before choosing this model.
The TZU-20 can form part of a coordinated surge protection arrangement. Depending on the installation, this may include a Type 1 SPD at the incoming supply, a Type 2 SPD at a downstream distribution board, and additional protection for sensitive equipment or signal lines.
Coordination requirements depend on the selected SPD combination, cable routing, installation conditions, and manufacturers' instructions. Do not assume that one cable separation distance is suitable for every installation.
A compatible surge protective device backup protection component, such as an SCB, may be required according to the product documentation and installation design. Confirm its specified ratings against the SPD requirements and prospective short-circuit conditions. A grounding busbar may also be required as part of the installation.
Correct protective-earth connections and short, appropriately routed SPD conductors are important to the overall protection result. Actual performance also depends on earthing quality, upstream protection, and the withstand capability of connected equipment.
The TZU-20 is designed for 35mm DIN rail mounting inside a suitable electrical enclosure. Its IP20 rating is intended for protected cabinet installation, not direct exposure to rain or outdoor weather.
Before installation, verify the supply voltage, earthing system, module configuration, upstream protection, and backup protection requirements. Follow the product wiring diagram and applicable electrical installation rules.
Check the visual status indicator during scheduled maintenance and after significant surge events. If the indicator identifies a failed module, arrange safe isolation and replace the affected module in accordance with the manufacturer's instructions.
For outdoor applications, the complete assembly requires an enclosure with suitable ingress protection and environmental suitability. The enclosure and wiring arrangement must also allow safe installation, inspection, and maintenance.
For distributors, panel builders, electrical contractors, and project buyers, the key selection documents are the datasheet for the exact configuration, the wiring diagram, and applicable test or compliance documents. These help verify the rated parameters and installation requirements before a product is specified.
If a project requires evidence of routine production testing, batch traceability, third-party testing, or compliance with a particular standard, confirm which records are available for the TZU-20. Testing procedures and compliance claims should be stated only when supported by the corresponding documentation.
The TZU-20 is specified as a Type 2 AC surge protective device for downstream surge protection. It should not replace a Type 1 SPD where the installation design requires Type 1 protection at the incoming supply.
In is the nominal discharge current rating, while Imax is the maximum discharge current rating under the specified 8/20 μs test conditions. They are separate ratings and should be compared using the applicable product specifications and test standard.
The L-pole and N-PE modules protect different electrical paths and have different specified maximum continuous operating voltages: 275V AC and 255V AC, respectively. Confirm the connection points and system compatibility using the manufacturer's wiring diagram.
The supplied product information specifies TN-S and TN-C-S systems. TT compatibility has not been established by the provided information. Confirm the N-PE arrangement, wiring requirements, and applicable backup protection with the manufacturer before selecting the device for a TT system.
The requirement depends on the product instructions, short-circuit withstand capability, and installation design. Confirm the specified backup protection type and ratings before installation.
The device has an IP20 rating and is intended for installation inside a suitable enclosure. Outdoor use requires a complete assembly with appropriate environmental and ingress protection.
Refer to the indicator markings and maintenance instructions for the exact model. If the module is identified as failed, isolate the circuit safely and replace the affected module according to the manufacturer's instructions.
Provide the supply voltage, earthing system, application, required quantity, destination market, and any project-specific technical requirements. These details help establish whether the 1P+N-PE configuration is suitable and which accessories or documents may be needed.
Share your system voltage, earthing arrangement, application, and required quantity with TU-SHAN Electric. Our team can help you evaluate whether the 1P+N-PE Type 2 AC Surge Protective Device 20kA matches your project requirements and identify the technical documentation needed for selection.
Address
No.51, Changjiang Road, Wenzhou Bridge Industrial Zone, Beibaixiang Town, Yueqing City, Zhejiang Province, China
Tel
